INSTALLATION INSTRUCTIONS FOR the SAS 9.3 TS1M0 DBRMs DOWNLOAD ON z/OS 


SAS 9.3 TS1M0 DBRM members for SAS/Access Interface to DB2

BEFORE DOWNLOADING:

This download addresses the fact that the DBRMs members that are
needed for the DB2 bind are not included as part of the install 
and must be downloaded separately.  

The following file(s) will be installed:

      * DBRM93_TS1M0_V8.xmit
             PDS in XMIT format.  It contains the DBRM members
             needed for the bind if you are accessing DB2 V8 NFM
             and running SAS 9.3 TS1M0.

      * DBRM93_TS1M0_V9V10.xmit
             PDS in XMIT format.  It contains the DBRM members
             needed for the bind if you are accessing DB2 V9 or 
             DB2 V10 NFM and running SAS 9.3 TS1M0.

INSTALLATION INSTRUCTIONS:

The following instructions describe the steps for extracting the
contents of the downloaded files, moving the files to your z/OS
system and installing the appropriate DBRM members.


STEP 1: PRE-ALLOCATE THE XMIT FILES ON z/OS (required)

  Pre-allocate 2 files on z/OS (e.g. 'sas.dbrm93.ts1m0.v8.xmit' and
  'sas.dbrm93.ts1m0.v9v10.xmit ') with the following DCBs.  Be sure 
  to check the space requirements on the download page.   

     Organization  : PS
     Record format : FB
     Record length : 80
     Block size    : 3120


STEP 2: FTP THE XMIT FILEs TO z/OS (required)

  FTP the appropriate XMIT files into the newly created files.  
  DBRM93_TS1M0_V8.xmit would be stored in 'sas.dbrm93.ts1m0.v8.xmit',
  DBRM93_TS1M0_V9V10.xmit would be stored in 'sas.dbrm93.ts1m0.v9v10.xmit'.  
  This can be done in one of 2 ways:

    Method 1) Download the packaged hot fix to your PC.  The
              packaged hot fix is a is a self extracting
              executable.  Launching the executable will extract
              the z/OS files to a default location

                   example: C:\zos\dbrm93

              You will be prompted during the extraction process
              to accept or overwrite the default unzip location.
              The remaining steps in these installation
              instructions assume that you have unzipped the
              files to the default location.

              After extracting the files, FTP the DBRM93_TS1M0_V8.xmit and 
              the DBRM93_TS1M0_V9V10.xmit files to your z/OS system by 
              doing a BINARY upload into the pre-allocated files created in step 1.

    Method 2) From z/OS, FTP to ftp.sas.com using
              userid=anonymous and password=your.email@address 

              Once you are logged on, cd into the following
              directory:
               /techsup/download/hotfix/dbrms/mvs
              
              Issue the following commands where
              'SAS.DBRM93_TS1M0_V8.xmit' and 'SAS.DBRM93_TS1M0_V9V10.xmit' are
              the filenames you created in step 1.

              binary
              get DBRM93_TS1M0_V8.xmit SAS.DBRM93_TS1M0_V8.xmit (rep 
              get DBRM93_TS1M0_V9V10.xmit SAS.DBRM93_TS1M0_V9V10.xmit (rep 
              quit


STEP 3: RECEIVE THE XMIT FILEs TO CREATE THE DBRMLIB PDS (required)

  On z/OS issue a RECEIVE command against the uploaded XMIT files
  as follows where 'sas.dbrm93.ts1m0.v8.xmit' and 
  'sas.dbrm93.ts1m0.v9v10.xmit' are the preallocated file in step 1. 

      receive indataset('sas.dbrm93.ts1m0.vx.xmit') 

  After doing this you will be prompted with something similar to
  the following:

     INMR901I Dataset DATA.SET.NAME from USERID on ????????
     INMR906A Enter restore parameters or 'DELETE' or 'END' +

  at this prompt you should enter something similar to the following where  
  sas.dbrm93.ts1m0.vx.dbrmlib will the name of your newly created PDS containing   
  the DBRM members:

     DA('sas.dbrm93.ts1m0.vx.dbrmlib')

  
This completes the download of the SAS 9.3 TS1M0 DBRM members on z/OS. 


NOTE: The following information should be given to the appropriate person responsible 
      for doing the DB2 bind:
   *  The name of the DBRMLIB data sets containing the SAS93 and SAS93X members
      that were created in the above step.   
   *  When performing the DB2 bind, point to that DBRMLIB data set.