INSTALLATION INSTRUCTIONS FOR the SAS 9.2 TS1M0, SAS 9.2 TS2M0 and SAS9.2 TS2M2 DBRMs DOWNLOAD ON z/OS 


SAS 9.2 TS1M0, SAS 9.2 TS2M0 and SAS9.2 TS2M2 DBRM members for SAS/ACCESS Interface to DB2

BEFORE DOWNLOADING:

This download addresses the fact that the DBRMs members that are
needed for the DB2 bind are not included as part of the install 
and must be downloaded separately.  

The following file(s) will be installed:

      * DBRM92_V7.xmit
             PDS in XMIT format.  It contains the DBRM members
             needed for the bind if you are accessing DB2 V7 or
             DB2 V8 in Compatibility Mode and running SAS 9.2 TS1M0, 
             running SAS 9.2 TS1M0, SAS 9.2 TS2M0 and SAS9.2 TS2M2.

      * DBRM92_V89.xmit
             PDS in XMIT format.  It contains the DBRM members
             needed for the bind if you are accessing DB2 V8 in
             New Function Mode or DB2 V9 and running SAS 9.2 TS1M0, 
             SAS 9.2 TS2M0 and SAS9.2 TS2M2.


INSTALLATION INSTRUCTIONS:

The following instructions describe the steps for extracting the
contents of the downloaded files, moving the files to your z/OS
system and installing the appropriate DBRM members.


STEP 1: PRE-ALLOCATE THE XMIT FILES ON z/OS

  Pre-allocate 2 files on z/OS (e.g. 'sas.dbrm92.v7.xmit' and 
  'sas.dbrm92.v89.xmit') with the following DCBs.    

     Organization  : PS
     Record format : FB
     Record length : 80
     Block size    : 3120


STEP 2: FTP THE XMIT FILES TO z/OS

  FTP the appropriate XMIT files into these newly created files.  
  DBRM92_V7.xmit should be stored in 'sas.dbrm92.v7.xmit' and DBRM92_V89.xmit
  should be stored in 'sas.dbrm92.v89.xmit'.  

    - Download the packaged hot fix to your PC.  The
      packaged hot fix is a is a self extracting
      executable.  Launching the executable will extract
      the z/OS files to a default location

          example: C:\Documents and Settings\userid\Local Settings\Temp

      You will be prompted during the extraction process
      to accept or overwrite the default unzip location.
      The remaining steps in these installation
      instructions assume that you have unzipped the
      files to the default location.

      After extracting the files, FTP the DBRM92_v7.xmit and
      the DBRM92_v89.xmit files to your z/OS system by doing a 
      BINARY upload into the pre-allocated files created in 
      step 1.



STEP 3: RECEIVE THE XMIT FILES TO CREATE THE DBRMLIB PDS

  On z/OS issue a RECEIVE command against the uploaded XMIT files
  as follows where 'sas.dbrm92.v7.xmit' and 'sas.dbrm92.v89.xmit' are
  the preallocated files in step 1. The RECEIVE will need to be done 
  against both of the XMIT files individually where vxx is either v7 or v89 
  using the above example names:

      receive indataset('sas.dbrm92.vxx.xmit') 

  After doing this you will be prompted with something similar to
  the following:

     INMR901I Dataset DATA.SET.NAME from USERID on ????????
     INMR906A Enter restore parameters or 'DELETE' or 'END' +

  at this prompt you should enter something similar to the following where  
  sas.dbrm92.vxx.dbrmlib will the name of your newly created PDS containing   
  the DBRM members:

     DA('sas.dbrm92.vxx.dbrmlib')

  
This completes the download of the SAS 9.2 DBRM members on z/OS.  The bind can now be done.  

NOTE: The following information should be given to the appropriate person responsible 
      for doing the DB2 bind:
   *  The names of the 2 DBRMLIB data sets containing the SAS92 and SAS92X members
      that were created in the above step. One data set will be used during the bind
      for accessing DB2 V7 and one data set will be used for accessing DB2 V8 or DB2 V9.  
   *  When performing the DB2 bind, point to the appropriate DBRM data set, rather 
      than specifying the DBRM data set created during the SAS install.